ArchLinux, nForce4: настройка сенсоров

1. Делаем раз:

   pacman -Sy lm_sensors

2. Редактируем /etc/rc.conf, в загружаемые модули добавляем (MODULES):

   i2c-nforce2 i2c-isa eeprom it87

3. В /etc/rc.local добавляем строчку

   sensors -s

4. Открываем /etc/modprobe.conf, добавляем:

   # I2C module options
   alias char-major-89 i2c-dev

5. Сохраняем патч ниже в файл nforce4-sensors.diff

   --- sensors.conf.orig 2005-10-03 03:38:49.000000000 +1100
   +++ sensors.conf 2006-06-18 23:13:52.000000000 +1100
   @@ -1504,7 +1504,7 @@
   # Voltage monitors as advised in the It8705 data sheet
   - label in0 "VCore 1"
   + label in0 "VCore"
   label in1 "VCore 2"
   label in2 "+3.3V"
   label in3 "+5V"
   @@ -1517,6 +1517,11 @@
   # vid is not monitored by IT8705F
   # comment out if you have IT8712
   ignore vid
   + ignore in1
   + ignore in5
   + ignore in6
   + ignore in7
   + ignore in8
   # Incubus Saturnus reports that the IT87 chip on Asus A7V8X-X seems
   # to report the VCORE voltage approximately 0.05V higher than the board's
   @@ -1524,10 +1529,11 @@
   # the next line should bring the readings in line with the BIOS' ones in
   # this case.
   # compute in0 -0.05+@ , @+0.05
   +compute in0 0.03+@ , @-0.03
   # If 3.3V reads 2X too high (Soyo Dragon and Asus A7V8X-X, for example),
   # comment out following line.
   - compute in2 2*@ , @/2
   + #compute in2 2*@ , @/2
   #
   compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
   compute in4 ((30/10) +1)*@ , @/((30/10) +1)
   @@ -1560,6 +1566,8 @@
   set in0_min 1.5 * 0.95
   set in0_max 1.5 * 1.05
   + #set in0_min 1.2
   + #set in0_max 1.8
   set in1_min 2.4
   set in1_max 2.6
   set in2_min 3.3 * 0.95
   @@ -1591,12 +1599,14 @@
   # (see ignore statement right below).
   label temp1 "M/B Temp"
   - set temp1_over 40
   + #set temp1_over 40
   + set temp1_over 45
   set temp1_low 15
   label temp2 "CPU Temp"
   - set temp2_over 45
   + #set temp2_over 45
   + set temp2_over 50
   set temp2_low 15
   -# ignore temp3
   + ignore temp3
   label temp3 "Temp3"
   set temp3_over 45
   set temp3_low 15
   @@ -1618,6 +1628,9 @@
   set fan2_min 3000
   # ignore fan3
   set fan3_min 3000
   + label fan1 "CPU fan"
   + label fan2 "CHA fan"
   + label fan3 "CHIP fan"
   # The following is for the Inside Technologies 786LCD which uses either a
   # IT8705F or a SIS950 for monitoring with the SIS630.

6. помещаем его в каталог /etc и делаем

   patch -p0

7. Вызываем sensors и любуемся.

© Hatred, 2006